![]() ![]() Hold down the BOTTOM LEFT BUTTON until the unit beeps - this may take up to 20 seconds.Scroll down until you see the SHOW SETTINGS sub-menu, and then press the corresponding menu button to select it.Press the TOP LEFT button to open the main menu.Power up your device ( HIGHLY RECOMMENDED to power it via USB source (such as a laptop, or really anything that has a USB port on it) rather than directly to the truck via the OBD-II interface.To begin the vin unlock code process, we’ll need the root (challenge) code, which is generated by your tuner. The Mini Maxx V2 is NOT currently supported.In the unlikely case of a delay in providing an unlock code, it would be required to keep constant power to the tuner otherwise your root code will not be the same, and your unlock code will be no good. It is recommended to have your tuner plugged into a computer's USB interface during this process.IF YOU HAVE OTHER OPTIONS THAT WERE PREVIOUSLY UNLOCKED (SUCH AS HIGH SULFUR/EMISSIONS DELETE PROGRAMMING ON STREET TUNERS, IN MOTION, ETC), THEN THESE FEATURES WILL BE SET BACK TO FACTORY STATUS AND THE ORIGINAL UNLOCK CODES WILL HAVE TO BE RE-ENTERED. THE VIN UNLOCK RESETS THE TUNER TO FACTORY DEFAULTS.VIN unlock codes are NCNR (Non-Cancellable/NON-REFUNDABLE) once orders have been submitted and payment has been processed.Do not power the unit down or exit out of the root code screen for any reason once you have submitted your order because the root code changes each time that menu is accessed, and your unlock code will be no good. Power Levels - DPF Removed (aftermarket exhaust) with H&S Mini Maxx without Pyrometer Connectionįord 6. *Duramax LML with H&S Mini Maxx without Pyrometer Connectionįord 6.4L with H&S Mini Maxx without Pyrometer Connectionįord 6.7L with H&S Mini Maxx without Pyrometer Connection Power Levels - DPF Present (stock exhaust) with H&S Mini Maxx without Pyrometer Connectionĭodge 6.7L with H&S Mini Maxx without Pyrometer Connectionĭuramax LMM with H&S Mini Maxx without Pyrometer Connection ![]() H&S Overdrive transmission software available for purchase for 6.7L Dodge Power Levels - Pre-DPF trucks with H&S Mini Maxx without Pyrometer Connectionĭodge 5.9L with H&S Mini Maxx without Pyrometer Connectionįord 6.0L with H&S Mini Maxx without Pyrometer Connection Transmission tuning included on the 6.4 Powerstroke.6.4 Powerstroke applications read from the factory manifold pyro and do not need an external pyrometer connection.Allows for use of aftermarket turbo kits with no trouble codes (Only 6.7 Cummins).Custom Mounting Solutions available HERE.Digital gauges to monitor up to 20 parameters.Internet updateable w/included SD Memory Card and USB Adapter.Turn off the EGR system without removing ANY parts.Allows removal of the entire EGR system including cooler with no trouble codes.Enable / Disable factory "special features".Speedometer recalibration for use of non-stock size tires or gearing.Approximate size: 3.5" x 2" (2" x 1.75" color screen) Black Maxx / Mini Maxx Size Comparison 1, 2.Precisely tune engine with HP increases of 0-250HP (dependent on application, see below chart).Usable on ANY of the above vehicle applications if previous truck is returned to stock tuning.Allows removal of the DPF system and ALL related sensors (nothing needs to go into the race exhaust or even be plugged in).Comes preloaded with DPF Present and DPF Removed capable tuning.2011 - 2014 Ford 6.7 Powerstroke F250-F550įeatures for Mini Maxx without Pyrometer Connection.Applications for Mini Maxx without Pyrometer Connection This H&S Mini Maxx without Pyrometer Connection cannot be used on any vehicles registered or certified for highway use. If using DPF/EGR removed tuning, this H&S Mini Max without Pyrometer Connection is intended SOLELY for closed-course racing use and is not street legal in ANY state. The H&S Mini Maxx without Pyrometer Connection is capable of disabling emissions equipment. ![]() Ford 6.4 Powerstroke trucks can use a factory sensor in the manifold to monitor EGT. We do, of course, recommend purchasing one for the 6.7 Cummins and 6.6 LMM Duramax so you can monitor your Exhaust gas temperatures and set your defuel levels based on EGTs. It will NOT harm your truck to run without a pyrometer probe installed. It is used for gauge display and for one of the defueling parameters. ![]() The Pyrometer connection is NOT necessary for the H&S Mini Maxx without Pyrometer to function correctly. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |